Watts Innovations Public Knowledge Base
  • WELCOME
  • Introduction
  • Aircraft
    • ⚫PRISM Sky
      • 📚PRISM Sky Manuals and Documentation
        • 📓PRISM Sky Flight Manual
        • 🗒️PRISM Sky Quick Start Guide
      • 🔎Remote ID
        • How Remote ID Works
        • Serial Numbers & Labeling
        • Registering PRISM Sky with the FAA
        • Configuration for Operators
        • Remote ID Status
        • Product Support & Notification
          • Making your PRISM Sky Remote ID Compliant
        • FAQ
      • 📌Safety Bulletins
      • ⚙️The Basics
        • Selecting a Ground Control Station
          • KONTACT GCS
          • PC, Laptop or Tablet GCS
        • Resetting to stock configuration
        • "Hot Swapping" Batteries
        • Registering for Suite & Activating PRISM Sky
        • Sensor Calibration
          • Compass Calibration
          • Gyroscope Calibration
          • Accelerometer Calibration
        • Communication Link C2
          • Radio Setup
            • Silvus Radio
              • Installing Silvus Antennas
              • Accessing the User Interface (Silvus)
            • DoodleLabs Radio
              • Installing DoodleLabs Antennas
              • Accessing the User Interface (DoodleLabs)
              • Changing the SSID
              • Changing basic radio settings
              • Accessing the Spectrum Scanner Tool
        • Attaching Motor Arms
        • Installing Propellers
      • 💻GCS Software
        • Watts AMC
          • System Requirements
          • Installing/Updating Watts AMC
          • Release Notes (Watts AMC)
      • ✈️Aircraft Firmware
        • AuterionOS for PRISM Sky
          • Downloading AOS for PRISM Sky
          • Connecting/Updating AOS for PRISM Sky
          • Release Notes (AOS)
      • 🏗️Payload Integrations
        • Payload Rail System
          • Installing & Removing Payloads
        • Payloads
          • Gremsy T3 PE Gimbal
            • Sony A7RIV
              • Formatting Storage Devices
              • Data Storage
          • DRS-25 Parachute
            • Installing the DRS-25 on PRISM Sky
            • Configuring the DRS-25 on PRISM Sky
            • Arming the DRS-25 on PRISM Sky
            • Repacking the DRS-25 Parachute
        • Controlling a device through PWM
      • ➕PRISM Sky Accessories
        • PRISM Sky Quick Release Battery Tray Set
        • PRISM Sky External GPS Mount
        • PRISM Sky Gremsy Damping Plate Assembly
        • PRISM Sky External Power Cables
        • Attaching LW20 leg to PRISM Sky
      • ⁉️PRISM Sky + KONTACT Troubleshooting Tips
    • 🔵PRISM Lite
      • PRISM Lite Manuals and Documentation
        • PRISM Lite Flight Manual
        • PRISM Lite Quick Start Guide
      • Remote ID
        • How Remote ID Works
        • Serial Numbers & Labeling
        • Registering PRISM Lite with the FAA
        • Configuration for Operators
        • Remote ID Status
        • Product Support and Notification
      • Safety Bulletins
      • The Basics
        • Installing SBus Receivers
          • Radio Calibration
          • Mapping Channels
      • GCS Software
        • QGroundControl
          • System Requirements
          • Installing/Updating QGroundControl
          • Release Notes (QGC)
        • Mission Planner
          • System Requirements
          • Installing/Updating Mission Planner
          • Release Notes (MP)
      • Aircraft Firmware
        • ArduCopter for PRISM Lite
          • Downloading ArduCopter for PRISM Lite
          • Connecting/Updating PRISM Lite
          • Release Notes (ArduCopter)
      • PRISM Lite Accessories
        • IDLINK
          • Configuration for Operators
            • Disabling the Serial Enumerator
    • 🔴PRISM
      • 📚Manuals & Documentation
        • 📘PRISM Flight Manual
        • ℹ️PRISM Quick Start Guide
      • 🔍PRISM Remote ID
      • 📌Safety Bulletins
        • PRISM SA01: Landing Gear Clamp
        • PRISM SA02: "Hot Plugging" Arm Socket
        • PRISM SB01: Coaxial Motor Mount Defect
      • ❓The Basics
        • Assembling PRISM
        • Attaching Motor Arms
        • Installing Propellers
        • Removing GPS's
        • PRISM Flight Modes
        • Propulsion System
        • PRISM Aircraft Weight
        • Battery Tips
        • Pairing a new Echosky to PRISM Air Unit
      • 📷PRISM Payload Integration
        • Payload Rail System
          • Installing Payloads
      • 💻WattsQGC Overview
      • 👨‍💻Firmware Updates
        • Updating WattsQGC
        • WattsQGC Release Notes
        • PRISM Release notes
        • Updating PRISM Firmware
      • 🚁PRISM Accessories
        • PRISM Carry Handle
        • PRISM External Data A Connector
        • PRISM External Power Cables
        • PRISM Quick Release Battery Tray Set
        • RFD900X Combo Set
        • PRISM: Here+ RTK Base & Tripod Combo
        • PRISM Extended Landing Gear Set
        • PRISM External GPS Folding Mount
  • Ground Control Station
    • 🎮KONTACT
      • KONTACT Quick Start Guide
  • POWER
    • ⚡Power & Charging
      • 🔋WATTS ULTRA LIGHT LiPo
        • 12S 16,000mAh
      • ✔️CHEK 12s Battery Monitor
      • 🔌EV Peak U4 Charger
      • 🦺General LiPo Battery Tips
  • PAYLOADS
    • 📦REEL Intelligent Delivery Winch
      • What Is In The Box?
      • Mounting, Connecting and button usage for REEL
        • How to use REEL in AMC
Powered by GitBook
On this page
  • Telemetry
  • Button Meanings and Uses

Was this helpful?

  1. PAYLOADS
  2. REEL Intelligent Delivery Winch
  3. Mounting, Connecting and button usage for REEL

How to use REEL in AMC

This document will explain how to use REEL in Auterion Mission Control

PreviousMounting, Connecting and button usage for REEL

Last updated 2 years ago

Was this helpful?

REEL is a plug and play product with PRISM Sky paired with Skynode and Auterion Mission Control. There is no additional software to download or utilize to use REEL with PRISM Sky. Simply connect the REEL to PRISM Sky via the included Winch Cable, power on the aircraft and ground station and then open AMC. The REEL control panel will appear in the bottom right of the program.

In the above graphic, you will see the control panel and various buttons as well as REEL telemetry information.

Telemetry

Current is the current in amperes being consumed by the motor inside of REEL. This value can vary depending on the weight of the package loaded onto the hook.

Torque is the value measured in n/cm that the motor is outputting at any given moment. This value can flucuate depending on package weight as well as if you are running a Delivery or not.

Spooled Out this is an estimation in feet based on the total line that was spooled onto the spool from Watts Innovations. It is an estimation based on motor rotations that is measured while performing a Delivery.

Lidar Distance is the distance in feet the Lidar sensor is from the ground. This is a measurement used by REEL to determine the delivery distance.

Button Meanings and Uses

Note: Using any of the functions on the REEL Control Panel will require the user to "Slide To Confirm" to ensure there are no accidental function triggers.

Press the Eject button on the control panel one time to move the eject pins into the open position. Press the button again to move the pins into the closed position.

Press the Freewheel button to unlock and present the hook, after the hook is present you can unspool it from the REEL as much as needed. If there is a knot in the line on the spool, you can use the Freewheel mode to pull the hook out and clear the line. Press the Freewheel button again and the line will be wound back onto the spool. Take note to apply pressure on the line when spooling back onto the spool to ensure a tight, evenly wound spool.

To load a package for the standard delivery mode, simply click on "Load Package" to unlock and present the hook. You can now load a package or payload onto the hook; and press the Load Package button again to pull the hook back into the REEL.

📦
Refer to the previous page for how to connect REEL to PRISM Sky.
REEL Control Panel in Auterion Mission Control