Watts Innovations Public Knowledge Base
  • WELCOME
  • Introduction
  • Aircraft
    • ⚫PRISM Sky
      • 📚PRISM Sky Manuals and Documentation
        • 📓PRISM Sky Flight Manual
        • 🗒️PRISM Sky Quick Start Guide
      • 🔎Remote ID
        • How Remote ID Works
        • Serial Numbers & Labeling
        • Registering PRISM Sky with the FAA
        • Configuration for Operators
        • Remote ID Status
        • Product Support & Notification
          • Making your PRISM Sky Remote ID Compliant
        • FAQ
      • 📌Safety Bulletins
      • ⚙️The Basics
        • Selecting a Ground Control Station
          • KONTACT GCS
          • PC, Laptop or Tablet GCS
        • Resetting to stock configuration
        • "Hot Swapping" Batteries
        • Registering for Suite & Activating PRISM Sky
        • Sensor Calibration
          • Compass Calibration
          • Gyroscope Calibration
          • Accelerometer Calibration
        • Communication Link C2
          • Radio Setup
            • Silvus Radio
              • Installing Silvus Antennas
              • Accessing the User Interface (Silvus)
            • DoodleLabs Radio
              • Installing DoodleLabs Antennas
              • Accessing the User Interface (DoodleLabs)
              • Changing the SSID
              • Changing basic radio settings
              • Accessing the Spectrum Scanner Tool
        • Attaching Motor Arms
        • Installing Propellers
      • 💻GCS Software
        • Watts AMC
          • System Requirements
          • Installing/Updating Watts AMC
          • Release Notes (Watts AMC)
      • ✈️Aircraft Firmware
        • AuterionOS for PRISM Sky
          • Downloading AOS for PRISM Sky
          • Connecting/Updating AOS for PRISM Sky
          • Release Notes (AOS)
      • 🏗️Payload Integrations
        • Payload Rail System
          • Installing & Removing Payloads
        • Payloads
          • Gremsy T3 PE Gimbal
            • Sony A7RIV
              • Formatting Storage Devices
              • Data Storage
          • DRS-25 Parachute
            • Installing the DRS-25 on PRISM Sky
            • Configuring the DRS-25 on PRISM Sky
            • Arming the DRS-25 on PRISM Sky
            • Repacking the DRS-25 Parachute
        • Controlling a device through PWM
      • ➕PRISM Sky Accessories
        • PRISM Sky Quick Release Battery Tray Set
        • PRISM Sky External GPS Mount
        • PRISM Sky Gremsy Damping Plate Assembly
        • PRISM Sky External Power Cables
        • Attaching LW20 leg to PRISM Sky
      • ⁉️PRISM Sky + KONTACT Troubleshooting Tips
    • 🔵PRISM Lite
      • PRISM Lite Manuals and Documentation
        • PRISM Lite Flight Manual
        • PRISM Lite Quick Start Guide
      • Remote ID
        • How Remote ID Works
        • Serial Numbers & Labeling
        • Registering PRISM Lite with the FAA
        • Configuration for Operators
        • Remote ID Status
        • Product Support and Notification
      • Safety Bulletins
      • The Basics
        • Installing SBus Receivers
          • Radio Calibration
          • Mapping Channels
      • GCS Software
        • QGroundControl
          • System Requirements
          • Installing/Updating QGroundControl
          • Release Notes (QGC)
        • Mission Planner
          • System Requirements
          • Installing/Updating Mission Planner
          • Release Notes (MP)
      • Aircraft Firmware
        • ArduCopter for PRISM Lite
          • Downloading ArduCopter for PRISM Lite
          • Connecting/Updating PRISM Lite
          • Release Notes (ArduCopter)
      • PRISM Lite Accessories
        • IDLINK
          • Configuration for Operators
            • Disabling the Serial Enumerator
    • 🔴PRISM
      • 📚Manuals & Documentation
        • 📘PRISM Flight Manual
        • ℹ️PRISM Quick Start Guide
      • 🔍PRISM Remote ID
      • 📌Safety Bulletins
        • PRISM SA01: Landing Gear Clamp
        • PRISM SA02: "Hot Plugging" Arm Socket
        • PRISM SB01: Coaxial Motor Mount Defect
      • ❓The Basics
        • Assembling PRISM
        • Attaching Motor Arms
        • Installing Propellers
        • Removing GPS's
        • PRISM Flight Modes
        • Propulsion System
        • PRISM Aircraft Weight
        • Battery Tips
        • Pairing a new Echosky to PRISM Air Unit
      • 📷PRISM Payload Integration
        • Payload Rail System
          • Installing Payloads
      • 💻WattsQGC Overview
      • 👨‍💻Firmware Updates
        • Updating WattsQGC
        • WattsQGC Release Notes
        • PRISM Release notes
        • Updating PRISM Firmware
      • 🚁PRISM Accessories
        • PRISM Carry Handle
        • PRISM External Data A Connector
        • PRISM External Power Cables
        • PRISM Quick Release Battery Tray Set
        • RFD900X Combo Set
        • PRISM: Here+ RTK Base & Tripod Combo
        • PRISM Extended Landing Gear Set
        • PRISM External GPS Folding Mount
  • Ground Control Station
    • 🎮KONTACT
      • KONTACT Quick Start Guide
  • POWER
    • ⚡Power & Charging
      • 🔋WATTS ULTRA LIGHT LiPo
        • 12S 16,000mAh
      • ✔️CHEK 12s Battery Monitor
      • 🔌EV Peak U4 Charger
      • 🦺General LiPo Battery Tips
  • PAYLOADS
    • 📦REEL Intelligent Delivery Winch
      • What Is In The Box?
      • Mounting, Connecting and button usage for REEL
        • How to use REEL in AMC
Powered by GitBook
On this page
  • Items you will need:
  • Tools you will need:
  • Installing the DRS-25 Parachute Mount

Was this helpful?

  1. Aircraft
  2. PRISM Sky
  3. Payload Integrations
  4. Payloads
  5. DRS-25 Parachute

Installing the DRS-25 on PRISM Sky

This page provides instructions for installing the DRS-25 on PRISM Sky.

PreviousDRS-25 ParachuteNextConfiguring the DRS-25 on PRISM Sky

Last updated 2 years ago

Was this helpful?

Items you will need:

Tools you will need:

Once your PRISM Sky has been removed from its transport container and is fully assembled, locate the area of installation which is on the left side of the aircraft (outlined in blue). Continue following the instructions below.

WARNING: It is recommended to disconnect all power supply before proceeding.

Installing the DRS-25 Parachute Mount

Step 1: Locate and remove the four (4) screws show in the image below using the 2.0mm Hex Driver, store screws in transport container:

  • Two (2) screws from the right side of the GPS mast outlined in red.

  • Two (2) screws from the left side of the carbon plate outlined in green.

NOTE: The 4 screws removed in Step 1 will be replaced with the four (4) M3x12 Stainless BLACK Button Head Bolts included in the PRISM Sky DRS-25 Parachute Combo.

Step 2: Line up the included PRISM Sky DRS-25 Mount over the screw hole holes from the previous step using the four (4) M3x12 Stainless BLACK Button Head Bolts and Blue 243 Loctite. Be sure to add a drop of Blue 243 Loctite to each of the four (4) bolts before installing mount to the airframe and tighten to 5.6 in-lbs.

STEP 3: Locate the DRS-25 Canister + Top (w/ SD Card installed) and ensure it is mounted to the bracket in the holes shown below (red arrows) and the SD card is installed (green arrow).

STEP 4: Line up the DRS-25 dovetail design with the mating dovetail mount while simultaneously pulling out on the safety knob indicated by the green arrow.

STEP 5: With the pin pulled, line up and slide on the DRS-25 Parachute System.

STEP 6: Ensure the DRS-25 is fully installed by ensuring the pin is in its locked position holding the device to the bracket.

STEP 7: Rotate your work area area to the front of the aircraft to install the PRISM Sky DRS-25 data and power cable.

STEP 8: Using the 2.0mm Hex Driver, remove the four (4) front facing screws (indicated by the red arrows) and the one (1) downward facing screw (indicated by the green arrow) holding the FPV camera cover in place.

STEP 9: Carefully hold the FPV camera cover making sure to not kink or damage the FPV cable harness or connector. Route the included PRISM Sky DRS-25 data and power cable through the rubber grommet located under the FPV camera and plug the parachutes data and power cable into the JST connector labeled WARNING PARACHUTE ONLY!

PRO-TIP: To prevent damaging the JST connector on the parachute data and power cable, feed the 5 pin connector side down and through the rubber grommet. Pull a majority of the cable through, enough to plug the JST into the connector on the aircraft and not have any cable slack left over so you can easily reinstall the FPV camera cover without damaging any wire harnesses.

WARNING: DO NOT plug the PRISM Sky DRS-25 data and power cable into anything other than the port labeled WARNING PARACHUTE ONLY! This will cause damage indefinitely and may void your warranty.

STEP 10: With the FPV camera cover still open, route the PRISM Sky data and power cable to the bottom side of the DRS-25 Parachute Mount and using Velcro or electrical tape secure the bottom 12mm rail system.

STEP 11: Using the 2.0mm Hex Driver, reinstall the four (4) front facing screws and the one (1) downward facing screw removed in Step 8. Add a drop of Blue Loctite to each of the 4 screws on the front of the cover before reinstalling. The single bottom screw does not require Blue Loctite.

NOTE: Do not apply Blue Loctite to the single bottom screw on the FPV camera cover as it will damage the plastic.

STEP 12: Insert the data and power cable by aligning the markings on the plug and the port. Then spin the silver portion of the plug to the right until it is tight. Ensure not to cross thread.

CAUTION: Users must use extreme caution when plugging in the parachute cable to ensure it is not plugged in incorrectly as this will ultimately fry the Skynode so it is imperative to line up the markings on the plug and the port.

NOTE: When the plug is tight, it is still a couple millimeters away from flush.

⚫
🏗️
How To | PRISM Sky DRS-25 Parachute Installation